nycsraka.blogg.se - Mac mini hard drive replacement ifixit

Mac mini hard drive replacement ifixit free#
Mac mini hard drive replacement ifixit mac#

It secures the SATA cable connector to the PCB of the hard drive.

Lift up the ribbon cable and carefully peel away the black tape underneath.

During reassembly, be sure to thread the hard drive cable through the slot in the drive tray.

Lift the hard drive up and remove it from the drive tray.

Remove the four (two on each side) 6.5 mm T8 screws securing the hard drive to the drive tray.

Mac mini hard drive replacement ifixit mac#

Lift the drive tray up out of the Mac mini.Remove the single 8 mm T6 screw securing the drive tray.Slide the power supply out of the mini, minding any cables that may get caught.Remove the 8 mm T6 screw securing the power supply.During reassembly ensure the power supply is inserted far enough into the case that the latch will engage with the groove.The AC-In latch should fit into the groove above it in the case.Rotate the AC-In connector 90 degrees counter-clockwise.

Mac mini hard drive replacement ifixit free#

To free the power supply from the case, grab the AC-In connector, which acts like a latch.

When replacing the clip, push it in until it stops-it should be secure even if there is no audible click.

Use tweezers or your fingers to pull the clip away from the AC-in socket, and remove it from the Mac mini.

The AC-in socket is secured with a small metal retaining clip.

Carefully slide the logic board assembly out of the Mac mini, minding any cables that may get caught.

Pull the DC-In cable connector straight out of its socket on the logic board.Remove the Mac mini Logic Board Removal tool.Cease prying when the removal tool makes contact with the opening in the rear case.The logic board and I/O board assembly should slightly slide out of the outer case. Carefully pull the tool toward the I/O board.Be sure the rods make contact with the case under the logic board before proceeding. Insert the Mac mini Logic Board Removal Tool into the two holes highlighted in red.Inserting instruments into any logic board holes other than the ones highlighted in red may destroy the logic board. To remove the logic board, the two cylindrical rods of the Mac mini Logic Board Removal Tool must be inserted into the holes highlighted in red.Remove the single 16 mm T6 screw securing the logic board.Lift the PCIe SSD connector up off its socket.Remove the two 2.6 mm T6 screws securing the PCIe SSD cable bracket.Skip the next three steps if your Mac mini only has a hard drive. The following three steps only apply to Mac minis equipped with a PCIe SSD.Use the tip of a spudger to disconnect the IR sensor cable connector by prying it straight up from its socket.Use the flat end of a spudger to lift the SATA cable connector up off of its socket on the logic board.

Remove the SATA cable connector bracket.Remove the 2.6 mm T6 screw securing the SATA cable connector bracket.Use the point of a spudger to lift the fan connector straight up out of its socket on the logic board.Pull the fan away from the SSD until you can easily access the fan connector.Lift the fan straight up to free the captive screw from its hole in the logic board.Do not attempt to remove the fan entirely.The fan connector is trapped under the edge of the fan and cannot be disconnected until the fan is moved.Remove the two 12 mm T6 screws from the fan.

Remove the antenna plate from the Mac mini.

Carefully pull the antenna cable out from the gap between the power supply and case.

Use the point of a spudger to lift the antenna connector straight up off its socket on the airport card.

Be careful not to lose the washer when removing the screw.

Remove the single 3.4 mm T6 screw and washer from the antenna cable.

With the I/O ports facing you, flip the antenna plate to the right to allow access to the antenna cable connector.

Do not completely remove the antenna plate it is still connected to the Mac mini by an antenna cable.

Remove the following TR6 screws from the antenna plate:.

Use the plastic opening tool to pry the bottom cover up off of the Mac mini.Pry near, but not right on the screw posts.The bottom cover is clipped onto three screw posts.If your Mac mini only has a hard drive, skip the steps about the PCIe SSD and its connector. This guide was made with a Fusion Drive Mac mini. Use this guide to replace the hard drive in your hard-drive-only or Fusion Drive Mac mini Late 2014.